New member introduction.

Subject: New member introduction. Mon Jan 27, 2020 5:32 pm

Hi,

Just dropping a note to introduce myself. I’m a gun collector and recently acquired a MGC MP40 replica.
I’m impressed at the general accuracy of this model compared to others I’ve seen. It goes well with my real G43 and K98’s. I believe it is a late model, display only, based on the plugged barrel and lack of striker and cuts. I’ll try and post some pictures below.

Subject: Re: New member introduction. Mon Jan 27, 2020 5:33 pm

More pictures, no serial # on barrel.

Subject: New member introduction Mon Jan 27, 2020 7:23 pm

Welcome to the club. Looks like you are right. It's a "RMI" later import version for the MP40 by MGC, they are getting harder to find these days without paying $$$$$.

Subject: Re: New member introduction. Tue Jan 28, 2020 11:46 am

Hi and welcome to the forum. Mp40 bolt looks in good condition, normally these are cut up as well on display models.

Subject: Re: New member introduction. Fri Jan 31, 2020 12:44 pm

Claymore, bolt face has the 45deg cut I think... Sad

Subject: Re: New member introduction. Mon Feb 03, 2020 12:25 pm

A big welcome here from me.

Sadly I can not help with the MGC MP40, but there should be members around here that know this model well.

Subject: Re: New member introduction. Mon Jun 08, 2020 1:12 am

Hi
I'm new to the forum, need to find out how the get the barrel off if some one can help.

Subject: New member introduction. Mon Jun 08, 2020 5:37 am

Nice RMI import MGC68. Much better then the DENIX model. Hold on to it they are getting hard to find without paying $$$$$ for one.

Subject: Re: New member introduction. Mon Jun 08, 2020 10:38 am

Stuart1 wrote:: Hi
I'm new to the forum, need to find out how the get the barrel off if some one can help.

Hi Stuart, welcome to the Forum.

Barrel removal is straight forward enough. Unscrew the barrel nut all the way, the barrel will lift away from the receiver without any problems.

_________________
Cerwyn

Hobby collector of Replica model guns and Militaria.
also member of Living History Reenactment Groups.

Subject: Re: New member introduction. Mon Jun 08, 2020 1:30 pm

Hi I can't see a barrel nut, but I have taken a few photos. I also need help on the body as some either screws have come out or bolts.
And I'm looking for side plates

Subject: Re: New member introduction. Mon Jun 08, 2020 1:42 pm

Stuart1 wrote:: Hi I can't see a barrel nut, but I have taken a few photos. I also need help on the body as some either screws have come out or bolts.
And I'm looking for side plates

Hi Stuart,

The barrel nut is the large nut between the barrel and receiver. Have a look at the MGC68 MP40 Instruction manual here

https://mp40modelguns.forumotion.net/t76-mgc68-mp40?highlight=mgc+mp40

Check the exploded diagram, the barrel nut is part number 5

Also the first diagrams show the nut being unscrewed with the original MGC spanner but it'll probably be a firm hand tight.

The photos at the start of this thread, first photo, show the barrel nut in place on the barrel

_________________
Cerwyn

Hobby collector of Replica model guns and Militaria.
also member of Living History Reenactment Groups.

Subject: Re: New member introduction. Mon Jun 08, 2020 2:05 pm

Subject: Re: New member introduction. Mon Jun 08, 2020 2:07 pm

Subject: Re: New member introduction. Mon Jun 08, 2020 2:08 pm

That's the one. Unscrew that and the whole barrel assembly will pull off the receiver

_________________
Cerwyn

Hobby collector of Replica model guns and Militaria.
also member of Living History Reenactment Groups.

Subject: Re: New member introduction. Mon Jun 08, 2020 2:13 pm

The second pair of photos you sent show where two, one each side, Allen bolts fit, see part 17 on the exploded diagram.

_________________
Cerwyn

Hobby collector of Replica model guns and Militaria.
also member of Living History Reenactment Groups.

» An introduction.
» INTRODUCTION - Hi Folks!
» Newbie introduction
» MGC or Marushin M16A1? (with Introduction!)
» new member